NHTSA Service Bulletin 11018588: 2022-2025 Mercedes-benz Amg Gt55
Official manufacturer communication context for 2022-2025 Mercedes-benz Amg Gt55, with affected products, buyer checks and links into Carchieve recall, problem and VIN research.
Reviewed June 2026 from NHTSA manufacturer communication and service bulletin records. Carchieve is independent and not affiliated with any vehicle manufacturer or government agency.
Complaint Cracking/clicking noise from underbody when driving slowly (around curves); see attachment. Cause Potential causes: Assembly of the underfloor paneling with unloaded body (results in tension after compression of vehicle in K0- design level) Relative movement between front and rear engine compartment lining Torque loss of the screw connection Accumulation of stones and dirt Remedy Screw connection in K0-design level (vehicle sitting on ground on it's own weight) and taking into account the correct screw sequence Additional screw connection points (minimization of relative movement) Increase in tightening torque Integration of spacer rings (reduction of accumulation of stones and dirt) In order to rule out that other component parts may be responsible for the noise, remove the underfloor paneling first. If the noise complaints are NO LONGER present after removal, proceed with underfloor paneling rework. Underfloor paneling rework 1. Order after-sales kit with item number A2326207003 for the rework. 2. After receiving the after-sales kit (A2326207003), check the contents: 22 screws (A0109902604) / 14 rivet nuts (A0009902349) / 4 spacer washers (A2326207203). If the content is complete, start rework in the next step. 3. Disassemble underfloor paneling. If front and rear engine compartment lining are bonded to one another, order new parts (A2326201101, A2326268900). 4. Clean underfloor paneling and integral carrier. 5. Mark four additional screw connection points on the front engine compartment lining (see attachment 1). See appendix 2 for dimensions. 6. Drill holes with d=9 mm on the markings. 7. Screw front and rear engine compartment lining together using the screw connection points already available (see attachment 3). Both linings are therefore aligned to one another. Important: Pay attention to alignment of the elongated holes on the external edges. 8. Drill into the rear engine compartment lining using the four additional holes with d=9 mm (see attachment 4). 9. Disassemble front and rear engine compartment lining. 10. Drill out three existing rivet nuts with d=9 mm (see attachment 5). 11. Insert seven new rivet nuts (A0009902349) (see attachment 6). 12. Drill out seven existing rivet nuts in the integral carrier with d=9 mm (see attachment 7). Caution: Do not damage integral carrier. 13. Remove remaining rivets that have fallen off from the integral carrier using a magnetic tube (see attachment 8). 14. Insert new rivet nuts (A0009902349) in the integral carrier (see attachment 9). 15. Fix four spacer rings (A2326207203) in place using bonding points between underfloor paneling and integral carrier (for position, see attachment 10 and attachment 11). Caution: No adhesive can be applied to the contact areas (risk of torque loss). 16. Install underfloor paneling on vehicle with 16 Nm (observe screw sequence in attachment 12). Important: Use screw item number A0109902604.
What this bulletin may mean before buying
Treat this as service research, not a verdict on one car. Before you buy, compare this communication with official recall campaigns, model-level owner complaint patterns, and the exact vehicle’s VIN-decoded specifications. A bulletin can help you ask a seller or dealer sharper questions about software updates, known repairs, warranty extensions and service history.
Affected products listed in this communication
Buyer checklist
- Run the 17-character VIN and confirm the year, make, model, engine and equipment match the listing.
- Check recall campaign pages for safety actions that may require dealer repair.
- Compare this bulletin with common problem pages for the same model and component area.
- Ask the seller or dealer whether the bulletin procedure, update or inspection has already been completed.
- Use the used-car buying checklist and get an independent inspection.
Frequently asked questions
What is NHTSA service bulletin 11018588?
Complaint Cracking/clicking noise from underbody when driving slowly (around curves); see attachment. Cause Potential causes: Assembly of the underfloor paneling with unloaded body (results in tension after compression of vehicle in K0- design level) Relative movement between front and rear engine compartment lining Torque loss of the screw connection Accumulation of stones and dirt Remedy Screw connection in.
Is a service bulletin the same as a recall?
No. A recall is a safety campaign with a required remedy for affected VINs. A service bulletin or manufacturer communication usually describes diagnostic, repair, software, warranty or service information.
How should a used-car buyer use this bulletin?
Use it as a research signal. Compare it with recalls, owner complaints, service records, a VIN report and an independent inspection before buying.
Check the exact VIN before you buy
Model-level pages show public safety patterns. A full VIN report helps confirm the exact vehicle, decoded specs, recall applicability and buyer checks.
Get Full Report